Product Description
CellarPro 1800 Duct HOOD Rear with Inline Fan (P/N 7409). This kit includes:
- 6-inch inline fan (120 CFM)
- Galvanized metal duct hood slides over the rear of the cooling unit and baffles the air intake and exhaust
- 8-foot power line provides switched power for the inline fan to match the on/off cycle of the wine cooling unit
The duct hood is designed with an easy-access panel to replace the air filter (sold separately), and openings for the drain line and power cord.
Ducting is not included with this kit. If you prefer, we also offer a kit that includes ducting.
Description
Allows CellarPro 1800 Series cooling units to be ducted up to 100 equivalent feet (50 feet per duct).
- Inline fan (3000RPM, 120 CFM) has a permanently lubricated, impedance protected motor
- Heavy gauge plated steel brackets
- Switched power to match the cooling unit
- Designed to fit over the rear of all CellarPro 1800 wine cooling units
- Includes an easy-access panel to replace air filters (sold separately)
- Grommet openings for the drain line and power cord
- Size:18 1/8w x 6 3/4d x 10 1/8h (in)
- Weight:8lb
- Power/Rating:115V, 60 Hz, 0.6 amps (Inline Fan)
- Warranty:1 Year
Cost: Price: $250.00 US
1800 Rear Duct Installation Instructions 1800-Rear Ducted Cut Sheet 1800-Rear Ducted Cut Sheet
Only logged in customers who have purchased this product may leave a review.
Related Products
CellarPro Mounting Clips 1800 2-Pk #1092-R
CellarPro Mounting Clips 1800 2-Pk (P/N 1092-R). Two mounting clips can attach anywhere along the front of CellarPro 1800 cooling units and offer predrilled slots for bolting to the ceiling of the wine cellar. Framing is required in or above the ceiling. Description; Mount to the front of CellarPro 1800 Series cooling units and are bolted to the ceiling inside the wine cellar. This is a retrofit item, and not for factory installation. Cost: Price: $10.00 US Options: Size:1.5w x 2d x 3/8h Weight:.1lb SKU:Clips (2)$10.00
Cold-Temperature Compressor Heater Factory Installed #1727
CellarPro Cold-Temperature Compressor Heater (P/N 32342 (1439)). Must be factory installed. When the cooling unit is exposed to cold temperatures, the refrigerant in the compressor can migrate into the crankcase oil when the compressor is not running. On startup, this can cause excessive motor wear and a loss of refrigeration efficiency. The compressor heater protects the compressor from damage in cold conditions below 40°F. Our self-regulating compressor heater attaches to the compressor and provides reliable peak heating during critical cold periods. Once the compressor starts up and/or temperatures start to rise, the compressor heater reduces its heating. Description; The compressor heater is required when the condenser (rear) side of CellarPro cooling units will be exposed to temperatures below 40°F. Enables cooling units to be exposed to temperatures below 40F Works effectively and reliably Promotes energy efficiency Extends compressor life Weight:.5 lb Power/Rating:120V / 60 Watts (at 0F) Warranty:1 Year SKU:32342 (1439)$135.00
1800 CellarPro Power Cord Modification #1098
CellarPro Power Cord Modification 1800 (SKU #1098). CellarPro 1800 Series wine cooling units can be modified so that the 8-foot, 16-gauge grounded power cord exits from the left side of the cooling unit, just below the power outlet, instead of from the rear of the cooling unit. This modification is designed for cooling unit installations where the power outlet is located INSIDE the cellar. Note: CellarPro VS Series cooling units are pre-configured to provide power either from the front or the rear of the cooling unit, at no additional charge, and do not require this modification. Description; If your power source is located inside the cellar, we can modify the power cord on 1800 Series cooling units to exit towards the front – rather than the rear – of the cooling unit. Cost: Price: $50.00 US Options: Size:8′ 16 Gauge$50.00
CellarPro Bottle Probe #1434
CellarPro Bottle Probe (P/N X/10K-E-PO-7″-10’CL2P-M232 (1061 rev01)). Bottle probes are recommended when the wine cooling unit will be placed remotely (ie the cold air will be ducted), and/or it cannot be placed near the top of the wine cellar. The bottle probe also can be used in odd-shaped wine cellars to control the cooling unit based on temperatures “around the corner”. Our bottle probe, which includes a rubber bottle stopper to avoid leaks and spills, can be inserted into a wine bottle filled with water and alcohol to avoid bacteria growth. The 10-foot cord allows the bottle to be placed almost anywhere inside the wine cellar. The other side of the probe is fitted with a jack that plugs directly into the face of the wine cooling unit. Bottle Probe Operating Instructions: When measuring liquid temperatures, the (HY) differential should be set at 1 degree (so that the wine liquid doesn’t fluctuate more than 1 degree.) When measuring air temperatures, the (HY) differential should be set at 4 degrees (the cooling unit will burn out prematurely if the unit cycles on’off every time the air temperature changes by 1 degree.) The probe or bottle/probe must be located in a location with good air movement in order to correctly register the temperature changes inside the cellar. When measuring air temperature with ducted systems, the ideal location for the bottle probe is in the return air register; when measuring air temperature with through-the-wall systems, the ideal location for the bottle probe is near the return air grill; when measuring liquid temperatures in bottles, the ideal location of the bottle is near the top of the racks with good airflow. In all cases, it is recommended to check the actual cellar temperature against the display temperature when the bottle probe is first setup and subsequently whenever the location moves. Refer to our Owners Manual for instructions how to change the HY differential .Bottle probes are compatible with all CellarPro wine cooling units. Description Bottle probe temperature sensor allows our wine cooling units to cycle on/off based on changes in liquid temperature inside the wine cellar. Digital temperature control based on liquid temperature Jack plugs directly into the face of the wine cooling unit Rubber bottle stopper fits most wine bottles; prevents spills and leaks 10-ft cord allows maximum flexibility in placement of wine bottle Recommended when the wine cooling unit will be placed remotely or low in the wine cellar Also can be used in odd-shaped wine cellars Size:10 Ft Cord Weight:.5 lb Warranty:1 Year SKU:X/10K-E-PO-7″-10’CL2P-M232 (1061 rev01) Options: Bottle Probe Extension Cord 25 Ft #1780 Bottle Probe Extension Cord 50 Ft #1781$135.00
1800 Condensate Drain Line Bottom #7431
CellarPro Condensate Drain Line BOTTOM 1800 (P/N 7431). Recommended when the wine cooling unit will be installed in a wine cellar, 1/2-inch ID condensate fitting and 8-foot clear vinyl tube allows overflow condensation to exit from the bottom of the cooling unit. DESCRIPTION: A condensate drain line is strongly recommended for wine cellar installations of 1800 Series wine cooling units. 1/2-inch ID condensate fitting 8-foot drain line Size:10 feet (drain line) Weight:.0001 lb Warranty:1 Year UPC:691054542433 COST: Price: $100.00 US OPTIONS: This option is designed to be factory-installed. If you already have purchased a CellarPro 1800 Series cooling unit, do not order this item; instead, you should order our Condensate Drain Line Retrofit Kit. Please note: The drain line is located 7-inches from the rear of the cooling unit. Therefore, the front 10 inches of the cooling unit MUST be located inside the wine cellar when used with this configuration.$100.00
1800 Condensate Drain Line REAR #1606
CellarPro Condensate Drain Line REAR 1800 (P/N 1606). Recommended when the wine cooling unit will be installed in a wine cellar, 1/2-inch ID condensate fitting and 8-foot clear vinyl tube allows overflow condensation to exit from the rear of the cooling unit. This option is designed to be factory-installed. Description; A condensate drain line is strongly recommended for wine cellar installations of 1800 Series wine cooling units. 1/2-inch ID condensate fitting 8-foot drain line Cost: Price: $75.00 US Options: If you already have purchased a CellarPro 1800 Series cooling unit, do not order this item; instead, you should order our Condensate Drain Line Retrofit Kit.$75.00
CellarPro 1800 Series Enhanced Warranty #1835
CellarPro 1800 Series Enhanced Warranty (SKU #1835). Designed to augment our standard warranty, our enhanced warranty provides the following additional coverage: Supplements the standard warranty during the 5-year period Covers the cost of all parts and labor to repair or replace defective parts during the warranty period Covers the cost of in-home service during the warranty period (up to 2 hours per incident) Covers shipping costs via standard ground service during the warranty period Please note the following terms and conditions: A deductible of $49 will be charged per incident Cleaning the coils and/or replacing the filter on the cooling unit are not covered by the extended warranty Scratches, blemishes and other damage caused during transit and/or normal wear-and-tear are not covered by the extended warranty Issues related to improper installation and/or usage of the products are not covered by the extended warranty The extended warranty is available exclusively to residential customers in the continental U.S. for use in non-commercial applications The extended warranty is not available for 220V models or CellarPro 1800XTSx The extended warranty does not cover accessories The extended warranty is not transferable Cost: Price: $79.00 US$79.00
Reviews
There are no reviews yet.